| Addressable Fire Alarm System... |
|
| Fire Alarm System is designed to detect the presence of fire by monitoring the environmental changes and to provide an early warning of fire that will notify people to evacuate and take immediate action to stop fire. The fire alarm system can also be integrated with AHU, AC Supply, Access Control, BMS etc…. Alarm can be triggered either by Automatic Detectors or by Manual call Points in case of emergency. |
|
 |
|
AG-I cable addressable fire alarm system consists of devices like Detectors, MCP, Hooter, Control Panel etc. All the devices require 24 volts DC and the power supply is drawn from main control panel through 1 cable (2 core). “During Fire” detector to panel and panel to hooters digital signals are sent through the same cable using power line communication technique.
Each and every devices in the network have unique address. “In case of fire” the respective area detector senses the fire and sends the data of fire and detectors address. On receipt of the signal the control panel display shows the exact zone number, zone location, device number and device location. The panel also sends signal to respective hooters, fire fighting systems, HVAC tripping etc.
Addressable Intelligent Fire Alarm Panel |
|
 |
| Addressable fire alarm panel is the device, which indicates the location of fire. A maximum of 255 devices can be connected to the panel (single loop). The advantage over this panel is entire programming can be done at site without depending manufacturer or installer. The fire/fault events are stored in memory to take the report |
| |
| |
|
|
|
| Addressable Intelligent Smoke Detector |
|
 |
| Addressable Intelligent Smoke Detector provides a revolutionary advance in early warning smoke detection technique. Its unique design, combined with intelligent sensing algorithm detects smoke with high sensitivity. Its performance is comparable to present technology, at a substantially lower installed cost. Additionally the preset values or the sensing levels can be adjusted from the panel. |
| |
| |
|
|
|
FEATURES:
» Easy to Install.Sleek, low-profile design
» Double LEDs blink in standby, providing 360° visibility
» Low current consumption
» Reverse polarity protection
TECHNICAL SPECIFICATION
Product code ALASD 601
Operating Voltage 15 to 24V DC
Maximum Standby Current 20mA
Sensor Optical
Operating Temperature -20°C to + 60°C
Humidity (noncondensing) 10 to 95% Relative
Addressable Intelligent Heat Detector |
|
 |
| Addressable Intelligent Heat Detector monitors and responds to the change in Ambient Temperature. Fire generally causes a rapid raise in temperature in the nearby location. The ALAHD series Heat Detectors senses the raise in temperature and signals the alarm if the temperature goes beyond 57°c. Additionally the preset values or the sensing levels can be adjusted from the panel. |
| |
| |
|
|
|
FEATURES:
» Easy to Install.Sleek, low-profile design
» Double LEDs blink in standby, providing 360° visibility
» Low current consumption
» Reverse polarity protection
TECHNICAL SPECIFICATION
Product code ALAHD 601
Operating Voltage 15 to 24V DC
Maximum Standby Current 20mA
Operating Temperature -20°C to + 60°C
Humidity (noncondensing) 10 to 95% Relative
Addressable Intelligent Photo Thermal Detector |
|
|
| Addressable Intelligent Photo thermal Detector is the combination of Smoke and Heat detector. The levels of the both photoelectric and heat sensors are continuously monitored by the detector and the alarm is triggered when the values go beyond the pre-set level. Additionally the preset values or the sensing levels can be adjusted from the panel. |
| |
| |
|
|
|
FEATURES:
» Easy to Install. Sleek, low-profile design
» Double LEDs blink in standby, providing 360° visibility
» Low current consumption
» Reverse polarity protection
TECHNICAL SPECIFICATION
Product code ALAMD 601
Operating Voltage 15 to 24V DC
Maximum Standby Current 20mA
Operating Temperature -20°C to + 60°C
Humidity (noncondensing) 10 to 95% Relative
Addressable Hooter |
|
 |
| Hooter is the device, which creates audible alarm to alert/evacuate the people. In case of Fire the panel sends the signal to trigger the hooter. On receipt of Silence signal the hooter stops alarm. |
| |
| |
|
|
|
| Addressable Manual Call Point |
|
 |
| Manual Call points are used to trigger the alarm manually and when activated, initiates an alarm on a fire alarm system. The Airlight Manual Call points is Switch Operated and this eliminates the replacement of glass and therefore reduces maintenance costs. In addition the call points include a number of features designed to make installation quick and easy. |
| |
| |
|
|
| |
| More >> |
| |
